風動礦用120型防爆切割鋸

FDJ-120型礦用管道切割鋸、電纜無火花切割鋸、FDJ-120型煤礦井下角鋼切割鋸、礦用防爆結構鋼切割鋸、FDJ-120型巷道U型鋼切割鋸、工字鋼無火花切割機、FDJ-120型軌道切斷切割鋸、煤礦井下鏈條截?cái)嗲懈钿彙DJ-120型礦用錨桿切割鋸、錨索氣動無火花手持式切割鋸…

FDJ-120/180/230型手持式風切割鋸使用：

1、了解所需切割的材料，如有必要可以通過空氣壓力來鋸片的轉動速度。

2、確保牢固固定了所需切割的材料，防止其。

3、氣動空氣馬達時，用閥桿，然后開始切割。

4、用鋸的重量來控制切割壓力。對于較軟的材料來說，這樣的重量已經足夠。過多的壓力會鋸片的速度。對于較硬的材料，可以通過加壓的來鋸片的轉動速度。切割是保持鋸筆直。鋸片的任何扭曲或歪斜都可能其使用壽命。（注意：避開切割后可能掉落的碎片。切割即將完成時，切勿使鋸碰到您的、工件或附近的其它人員。）

5、關閉空氣馬達時，釋放閥桿。

6、下次切割開始前，鋸片必須保持運動狀態。氣動鋸時，鋸片不能任何表面。

7、斷開空氣軟管時，關閉空氣軟管閥。斷開前，先打開空氣閥給軟管減壓。

8、更換鋸片前，務必?cái)嚅_空氣軟管，并推動閥桿以釋放掉馬達內的壓力。

9、順時針轉動手柄以便釋放鋸片導桿上的張力。然后釋放側面板的鎖以便打開側面板。然后從驅動輪上取下鋸片并將其從鋸帶導桿上松開。

聯系人金經理電話13934240041

FDJ-120 type mine pipe cutting saw, cable no spark cutting saw, FDJ-120 type coal mine angle cutting saw, mine explosion-proof structure steel cutting saw, FDJ-120 type tunnel U type steel cutting saw, I-beam without spark cutting machine, FDJ-120 type track cutting cutting saw, cut off the chain of coal mine, FDJ-120 mine bolt cutting saw cutting saw, anchor pneumatic hand-held cutting saw no spark...
FDJ-120/180/230 handheld wind cutting saw:
1. Understand the material that needs to be cut, such as the speed of rotation of the saw blade by air pressure.
2, ensure that the required cutting materials are firmly fixed to prevent them.
3, pneumatic air motor, use the stem, and then start cutting.
4, use the weight of the saw to control the cutting pressure. This weight is enough for softer materials. Too much pressure can see the speed of the blade. For harder materials, the speed of the rotation of the saw blade can be made by pressure. The cutting is to keep the saws straight. Any twist or skew of the saw can be used for its life. (notice: avoid debris that may fall after cutting. When the cutting is about to be completed, do not make the saw touch your, the workpiece, or the other people in the vicinity.
5. When the air motor is closed, the stem is released.
6. The saw blade must remain moving before the next cutting begins. When a pneumatic saw is used, the saw blade is not on any surface.
7. When the air hose is disconnected, the air hose valve is closed. Before disconnecting, open the air valve and decompress the hose.
8. Before replacing the saw, be sure to disconnect the air hose and push the stem to release the pressure of Madane.
9, rotate the handle clockwise so as to release the tension on the sawing guide rod. Then release the lock of the side panel so as to open the side panel. Then remove the blade from the drive wheel and release it from the sawing guide rod.